DRG Motor keeps the 110 kW (150 HP) three-phase asynchronous electric motor ready in a 315-frame cast-iron housing, in 3000, 1500 and 1000 rpm options, and ships it fast from İzmir to anywhere in Türkiye. This is the heaviest end of the catalogue; here the choice is set not by the kilowatts but by the machine’s speed, the torque at the shaft and the current at the panel.

110 kW grey 315-frame cast-iron DRG three-phase asynchronous electric motor, ready delivery and fast dispatch

DRG Motor is a manufacturer, supplier and seller of electric motors. You can choose the 110 kW electric motor by power and speed in the online electric motor shop, and see the models in this class together in the three-phase asynchronous electric motors category. The heavy-class housing is covered in our cast-iron frame high-kW motors article.

Where does 110 kW work?

A 315-frame electric motor is no longer a small drive unit; it is the plant’s main machine. In the field we meet 110 kW mostly on large process and centrifugal pumps, centrifugal and screw compressor sets, crusher and mill lines in cement and mining, high-flow forced-draught fans and blowers, large extruder and mixer shafts, and water and wastewater pumping stations. What they share: the load has high inertia, start-up takes time, and the stress on the housing even on the 2-pole model is in a different league from small ratings.

So on a 110 kW order, "how many kW" is only the start. The same power comes in three speeds, two shaft diameters and different load characters; the machine tells you the right combination, and we keep that combination ready.

The same 110 kW, three speeds: 315S and 315L frame

Speed is set by the number of poles: 2 poles ~3000 rpm, 4 poles ~1500 rpm, 6 poles ~1000 rpm. With power fixed at 110 kW, torque at the shaft grows as speed falls; the frame moves from 315S to 315L and the shaft from 65 mm to 85 mm. For a rough first check T = 9550 · P / n is a guide. The torque figures below are approximate against synchronous speed and a little higher at the rated speed on the nameplate.

ModelSpeed / frameTorque (approx.)Rated current (400 V)
DRG DRG-315S-23000 rpm · 315S350 Nm185.0 A
DRG DRG-315S-41500 rpm · 315S700 Nm187.0 A
DRG DRG-315L1-61000 rpm · 315L1050 Nm196.0 A

In practice the match is: 2 poles (3000 rpm) for fast centrifugal pumps and compressors, 4 poles (1500 rpm) for the most-requested general drives, 6 poles (1000 rpm) for hard-starting mills and slow loads. Picking the speed also means picking the shaft, coupling and pulley; keep our shaft diameter by kW table to hand for the dimensions.

Click to see current electric motor prices and order nowSEE PRICES →

Shaft, mounting and lifting: the weight of the 315 frame

At 110 kW the DRG range is offered only in a cast-iron (GG) housing; aluminium is not an option at this scale. The shaft diameter grows with speed: 65×140 mm on the 3000 rpm model, 85×170 mm on the 1500 and 1000 rpm ones. The mounting type must be settled up front; you can find the difference between foot (B3), flange (B5) and combined (B35) in our mounting types comparison article.

A 315-frame electric motor is not a one-person lift. Lowering it to the floor, seating it on the base and aligning the coupling call for a forklift or crane, use of the lifting eye on the housing, and a two-person crew planned from the start. Base flatness and alignment directly affect bearing life at this scale; stating the mounting type and shaft size at order time is the easiest way to avoid surprises on site.

Panel and connection: 400/690 V and starting

The 110 kW models are wound 400/690 V (delta at 400 V, star at 690 V). On the common 400 V three-phase supply this electric motor runs in delta (Δ). This should not be confused with the 230/400 V winding of small ratings; a wrong connection is a leading cause of early failure in this class.

The rated current at 400 V changes with speed, rising a little as the speed falls. These values are the starting point for thermal relay setting, contactor and cable sizing. At 110 kW the starting current is a multiple of the rated current, so direct starting is not used at this scale; star-delta or a soft starter is assessed separately. Always set protection and cross-section to the real value on the motor nameplate; do not work under live power, and leave connection and measurement to authorised electrical staff. Our cable size calculator and motor current chart help at this step.

Fast dispatch from the warehouse and İzmir-based delivery

DRG Motor is based in İzmir and ships fast by cargo to all of Türkiye, including that city. As standard speed options at a rating as commonly requested in heavy industry as 110 kW are kept ready in cast-iron housings, the time between order confirmation and dispatch is short. We reach İzmir, İstanbul, Bursa, Kocaeli, Ankara, Konya or any province of Anatolia with the same approach; our physical location is in İzmir only, and other provinces are served by cargo.

Logistics at this power run differently from small motors: packing, lifting points and vehicle type are planned by weight. To shorten the time on an urgent renewal of a stopped line, send your model and delivery province up front; we set the right speed and build the fastest shipping route together.

Four points to settle before ordering

Four pieces of information are enough to base a 110 kW order on a solid choice:

  1. Speed: the speed your machine needs (3000, 1500 or 1000 rpm).
  2. Mounting and shaft: foot (B3), flange (B5) or combined (B35); a 65×140 or 85×170 mm shaft.
  3. Voltage and starting: the site supply (commonly 400 V → delta) and whether the panel uses star-delta or a soft starter.
  4. Delivery province: the city it goes to, for the shipping plan and lifting arrangement.

With these you can select the right model in the electric motor shop and complete the order, and ask us wherever you are unsure. If you are renewing an existing unit, the most practical way is to photograph the old electric motor’s nameplate and send it to us.

Send a photo of your current motor nameplate and we will find the suitable DRG model together.Send on WhatsApp

See the current options and prices for the 110 kW electric motor in the shop.SEE PRICES

Frequently asked questions

How many HP is 110 kW?

110 kW is about 150 HP (1 HP ≈ 0.746 kW). Buyers looking for a "150 HP electric motor" are pointed to this power class too.

Is a 110 kW electric motor available in aluminium?

At this rating the housing is cast iron. DRG’s aluminium range stays at smaller powers; in heavy classes like 110 kW the load calls for the 315 cast-iron frame.

Which speed should I choose?

Your machine sets the speed: 3000 rpm for fast pumps and compressors, 1500 rpm for general drives, 1000 rpm for high-torque slow loads. If unsure, describe your application or check the electric motor calculator.

How long does delivery take?

As the standard speed options are kept ready, dispatch is quick; for a firm day just send your model and province. Because of the weight, lifting and vehicle arrangements are planned together from the start.

Electric Motors Related to This Topic — Models and Current Prices

Suitability is not decided by power alone: compare the speed, voltage, mounting, shaft and fixing dimensions of your machine with the product data; if unsure, send us the nameplate of your current motor.

ALL MODELS AND DETAILS IN THE ONLINE SHOP →