The 90 kW (about 120 HP) three-phase asynchronous electric motor waits ready at DRG Motor in a cast-iron housing, in 3000, 1500 and 1000 rpm options, and ships fast from İzmir to anywhere in Türkiye. At this rating the key question is not "how many kW" but which speed, which current, and how it gets down to the floor.
DRG Motor is a manufacturer, supplier and seller of electric motors, with a range from 0.25 kW up to 355 kW. You can choose the 90 kW electric motor by speed in the online electric motor shop, and see all the models of this class side by side in the three-phase asynchronous electric motors category.
Where does 90 kW earn its keep?
90 kW is one of a plant’s main-drive muscles. In the field we meet it most on mining and cement mills, large jaw and impact crushers, high-flow water transfer and deep-well pump sets, big screw air compressors, high-pressure forced-draught and exhaust fans, and heavy conveyor and belt drives. The load carries real inertia; starting is not easy, so the panel that drives it has to be set up correctly from the start, just like the motor itself.
So at 90 kW, picking a model is not a one-line power choice. The same 90 kW comes in three speeds, two frame sizes (280M and 315M) and three shaft diameters; the machine you drive and the panel dictate the right combination.
Three speeds, three pole counts: 3000, 1500, 1000 rpm
Speed is set by the number of poles. With power fixed at 90 kW, torque at the shaft grows fast as speed falls, and the frame size and shaft diameter grow with it. T = 9550 · P / n gives a rough first idea. The torque figures below are approximate against synchronous speed and a touch higher at the rated speed on the nameplate.
| Model | Speed / frame | Torque (approx.) | Rated current (400 V) |
|---|---|---|---|
| DRG DRG-280M-2 | 3000 rpm · 280M | 287 Nm | 152.0 A |
| DRG DRG-280M-4 | 1500 rpm · 280M | 573 Nm | 155.0 A |
| DRG DRG-315M-6 | 1000 rpm · 315M | 860 Nm | 161.0 A |
The shaft side thickens with speed too: a 65×140 mm shaft on the 3000 rpm frame, 75×140 mm on the 1500 rpm, 85×170 mm on the 1000 rpm. So setting the speed also sets the coupling, pulley and bearing calculation. Two poles for fast compressors and pumps, four poles for the most-requested general-drive middle ground, six poles for high-torque slow loads are the first matches that come to mind.
Click to see current electric motor prices and order nowSEE PRICES →
Why cast iron, and what changes at this weight
At 90 kW the DRG range comes only in a cast-iron (GG) housing; aluminium is not even on the table at this scale. The mass of the casting keeps the machine settled on crusher, mill and compressor lines dominated by shock starts and continuous vibration, absorbs vibration and spares the bearing side. In practice you need not debate the housing material; this is the standard at this rating.
The real difference shows in the weight. A 90 kW electric motor runs to hundreds of kilos and cannot be handled by hand at all. Unloading from the vehicle, seating on the base and alignment need a crane or forklift, slings suited to the lifting eye on the housing, and an experienced crew planned from the start. Settling the mounting type (foot B3, flange B5 or combined B35) at order time removes the "where and how does this sit" question when it arrives on site.
90 kW at the panel: 400 V current and soft starting
The 90 kW models are wired 400/690 V; on the common 400 V three-phase supply this electric motor runs in delta (Δ), in star (Y) at 690 V. It should not be confused with the 230/400 V motors at smaller ratings, and a wrong connection is a leading cause of the most damaging early failures in this class.
The rated current at 400 V changes with speed: in the table you see 152 A at 3000 rpm, 155 A at 1500 rpm and 161 A at 1000 rpm. These are the starting point for the contactor, cable cross-section and protection setting. At 90 kW the starting current reaches multiples of the rated current, so direct starting is not chosen in practice; star-delta or, most often, a soft starter / drive is assessed for the launch. Always set protection and cross-section to the real value on the motor nameplate; do not tamper with the system under live power, and leave connection and measurement to authorised electrical staff. Our cable size calculator and motor current chart give the starting values at this step.
Ready delivery and heavy-load logistics
DRG Motor is based in İzmir and reaches all of Türkiye, that province included, by fast cargo. As the standard speed options at a rating as regularly requested in heavy industry as 90 kW are kept ready in cast-iron housings, the time between order confirmation and dispatch is short. We ship to İzmir, İstanbul, Bursa, Kocaeli, Ankara, Gaziantep or any industrial zone in Anatolia with the same approach.
Logistics at this weight run apart from small-motor cargo: packing, lifting points and vehicle type are chosen by housing weight. On the urgent renewal of a stopped main line, the most time is saved by settling the model and delivery province up front; we work out the right speed and the shortest shipping route together.
Four points before ordering
Four pieces of information are enough to base a 90 kW order on a solid choice:
- Speed: the speed your machine needs (3000, 1500 or 1000 rpm).
- Mounting and shaft: foot (B3), flange (B5) or combined (B35); a 65×140, 75×140 or 85×170 mm shaft.
- Starting: star-delta, soft starter or drive at the panel, and the supply voltage (commonly 400 V → delta).
- Delivery province and site: the destination city and whether a crane/forklift is on site; the shipping and lifting plan follows from this.
With these four points you can select the right model in the electric motor shop and complete the order, and ask us wherever you hesitate. If you are renewing an existing unit, the most practical way is to photograph the old electric motor’s nameplate before removal and send it to us.
Send a photo of your current motor nameplate and we will find the suitable DRG model together.Send on WhatsApp
See the by-speed options and prices for your 90 kW electric motor in the shop.SEE PRICES
Frequently asked questions
How many HP is 90 kW?
By 1 HP ≈ 0.746 kW, 90 kW is about 120 HP; in catalogue terms it is usually called the 125 HP class. Buyers looking for a "120 HP" or "125 HP electric motor" are pointed to this power too.
Is a 90 kW electric motor available in aluminium?
No. At this rating the housing is cast iron; DRG’s aluminium range stays at small powers. In a heavy class like 90 kW the load calls for cast iron.
How do I get a 90 kW motor down to the floor?
With slings suited to the lifting eye on the housing, using a crane or forklift. It cannot be carried by one person; unloading, seating on the base and alignment need a crew and gear set aside from the start. Share the delivery province and site conditions at order time and we plan the lifting arrangement together.
Which speed should I choose?
Your machine sets the speed: 3000 rpm for fast compressors and pumps, 1500 rpm for general drives, 1000 rpm for high-torque slow loads. If unsure, describe your application or use the electric motor calculator.
Electric Motors Related to This Topic — Models and Current Prices
Suitability is not decided by power alone: compare the speed, voltage, mounting, shaft and fixing dimensions of your machine with the product data; if unsure, send us the nameplate of your current motor.
90 kW Three-Phase Motor 3000 rpm – DRG-280M-2 Cast Iron
- 90 kW · 3000 rpm (2 poles)
- Cast iron frame · IEC 280M
- Shaft: 65 × 140 mm
90 kW Three-Phase Motor 1500 rpm – DRG-280M-4 Cast Iron
- 90 kW · 1500 rpm (4 poles)
- Cast iron frame · IEC 280M
- Shaft: 75 × 140 mm
90 kW Three-Phase Motor 1000 rpm – DRG-315M-6 Cast Iron
- 90 kW · 1000 rpm (6 poles)
- Cast iron frame · IEC 315M
- Shaft: 85 × 170 mm













