The 55 kW three-phase asynchronous electric motor is the rating you want back in service fast when a line has stopped. DRG Motor keeps this power ready in a cast-iron housing, in 3000, 1500 and 1000 rpm, and ships it fast from İzmir to anywhere in Türkiye. Do not reduce the choice to one figure: the same 55 kW splits into three models by the speed your machine needs and the current at the panel.
DRG Motor is a manufacturer, supplier and seller of electric motors. You can choose the 55 kW electric motor by power and speed in the online electric motor shop, and see the models in this class together in the three-phase asynchronous electric motors category.
How does fast dispatch from the warehouse work?
At heavy ratings the first question is lead time, because when a 55 kW unit stops, the line behind it stops too. DRG Motor’s İzmir base speeds things up here: the moment the order is confirmed, dispatch is prepared, the shipment leaves İzmir and reaches your address by carrier. İzmir itself, İstanbul, Bursa, Kocaeli, Ankara, Gaziantep or any province of Anatolia is served the same way.
Logistics at this scale differ from small motors. Packing, lifting points and vehicle type are planned directly by weight, so before quoting a day we want your model and the destination province. We do not promise an exact hour, but on an urgent renewal we work out the fastest shipping route with you.
Which machines run on the 55 kW class?
This power is main-drive territory. In the field we meet 55 kW most often in front of large screw compressor sets, high-flow submersible and centrifugal pump stations, stone and marble gang-saw and crusher lines, extruder and granulator shafts, large forced-draught fans and dust-collection systems, and heavy conveyor drives. In all of them the load is hard, inertia is high and the start stresses the housing severely.
With such a load, saying "make it 55 kW" is only the start. Pick the wrong speed and the same power will not fit; so alongside the kilowatts you need to settle speed and torque up front.
Click to see current electric motor prices and order nowSEE PRICES →
Three speeds, three torques: 3000, 1500, 1000 rpm
Speed is set by the number of poles; with power fixed at 55 kW, torque at the shaft grows as speed falls, and so do the frame size and shaft diameter. For a rough first check T = 9550 · P / n is a guide. The torque figures below are approximate against synchronous speed and a little higher at the rated speed on the nameplate. Each model in the table links to its product page.
| Model | Speed / frame | Torque (approx.) | Rated current (400 V) |
|---|---|---|---|
| DRG DRG-250M-2 | 3000 rpm · 250M | 175 Nm | 93.5 A |
| DRG DRG-250M-4 | 1500 rpm · 250M | 350 Nm | 97.6 A |
| DRG DRG-280M-6 | 1000 rpm · 280M | 525 Nm | 98.1 A |
Speed also sets the coupling and bearing side: shaft diameter is 60×140 mm on the 3000 rpm model, 65×140 mm on the 1500 rpm one, 75×140 mm on the 1000 rpm one. Two poles is the first match for fast pumps and compressors, four poles the most-requested middle ground for general drives, six poles for hard-starting slow loads.
Cast-iron housing and the weight of 55 kW
At 55 kW the DRG range comes only in a cast-iron (GG) housing; aluminium is not an option at this scale. The mass of cast iron steadies the machine on crusher, gang-saw and compressor lines dominated by shock starts and continuous vibration, which helps the bearing side. So you do not decide the housing material separately; cast iron is the standard here.
The weight has a clear meaning on site: a 55 kW electric motor is not a one-person lift. Lowering it, seating it on the base and aligning it call for a forklift or crane, a proper lifting eye and a two-person crew planned from the start. Settling the mounting type (foot B3, flange B5 or combined B35) at order time is the shortest way to avoid surprises in the field.
The panel side: 400/690 V and starting
The 55 kW models are wired 400/690 V; on the common 400 V three-phase supply this electric motor runs in delta (Δ) and in star (Y) at 690 V. It should not be mixed up with the 230/400 V motors at smaller ratings; a wrong connection is among the leading causes of early failure in this class.
The rated current at 400 V changes with speed: about 93.5 A at 3000 rpm, 97.6 A at 1500 rpm and 98.1 A at 1000 rpm. These are the starting point for thermal relay setting, contactor and cable sizing. At 55 kW the starting current is a multiple of the rated current, so direct starting is usually avoided in the panel; star-delta or a soft starter is assessed separately. Always set protection and cross-section to the value on the motor’s own nameplate; isolate the supply and confirm it is dead, and leave connection and measurement to authorised electrical staff. Our cable size calculator and motor current chart make this step easier.
Four points to settle before ordering
Four pieces of information are enough to base a 55 kW order on a solid choice:
- Speed: the speed your machine needs (3000, 1500 or 1000 rpm).
- Mounting and shaft: foot (B3), flange (B5) or combined; a 60×140, 65×140 or 75×140 mm shaft.
- Voltage and starting: the site supply (commonly 400 V → delta) and whether the panel uses star-delta or a soft starter.
- Delivery province: the city it goes to, for the shipping plan and lifting arrangement.
With these you can select the right model in the electric motor shop and complete the order, and ask us wherever you are unsure. If you are renewing an existing unit, the most practical way is to photograph the old electric motor’s nameplate and send it to us.
Send a photo of your current motor nameplate and we will find the suitable DRG model together.Send on WhatsApp
See the current options and prices for your 55 kW electric motor in the shop.SEE PRICES
Frequently asked questions
How many HP is 55 kW?
55 kW is about 75 HP (1 HP ≈ 0.746 kW). Buyers looking for a "75 HP electric motor" are pointed to this power class too.
Is a 55 kW electric motor available in aluminium?
At this rating the housing is cast iron. DRG’s aluminium range stays at smaller powers; in heavy classes like 55 kW the load calls for a cast-iron housing.
Which speed should I choose?
Your machine sets the speed: 3000 rpm for fast pumps and compressors, 1500 rpm for general drives, 1000 rpm for high-torque slow loads. If unsure, describe your application or check the electric motor calculator.
How long does delivery take?
As the standard speed options are kept ready in cast-iron housings, dispatch is quick. For a firm day send your model and province; because of the weight, lifting and vehicle arrangements are planned together from the start.
Electric Motors Related to This Topic — Models and Current Prices
Suitability is not decided by power alone: compare the speed, voltage, mounting, shaft and fixing dimensions of your machine with the product data; if unsure, send us the nameplate of your current motor.
55 kW Three-Phase Motor 3000 rpm – DRG-250M-2 Cast Iron
- 55 kW · 3000 rpm (2 poles)
- Cast iron frame · IEC 250M
- Shaft: 60 × 140 mm
55 kW Three-Phase Motor 1500 rpm – DRG-250M-4 Cast Iron
- 55 kW · 1500 rpm (4 poles)
- Cast iron frame · IEC 250M
- Shaft: 65 × 140 mm
55 kW Three-Phase Motor 1000 rpm – DRG-280M-6 Cast Iron
- 55 kW · 1000 rpm (6 poles)
- Cast iron frame · IEC 280M
- Shaft: 75 × 140 mm













