A 30 kW three-phase electric motor is a power step you meet on press lines, stone crushers, large compressors, heavy conveyor drives and high-flow pump sets. DRG Motor builds this power in a cast iron housing with 2, 4 and 6 poles (3000, 1500 and 1000 rpm) and ships it from İzmir to anywhere in Türkiye on a ready-to-deliver, fast-dispatch basis.

Grey cast iron DRG asynchronous electric motor illustrating the 30 kW three-phase electric motor article

DRG Motor is a manufacturer, supplier and seller of electric motors. You can browse the 30 kW class by power and speed in the online electric motor shop and see the whole group together in the three-phase asynchronous electric motors category.

Where a 30 kW motor earns its keep

This is not a small-workshop size; it carries the line. In the field it turns up on marble and granite crushers, plastic and rubber extruder drives, large hydraulic power packs, and belt conveyors in cement and mining plants. The common thread: heavy load, strong vibration, costly downtime. So when you pick 30 kW, look at the housing and the speed together, not just the power figure.

30 kW options at DRG

All three models are 30 kW (about 40 HP), all cast iron, all wound for 400/690 V (Δ/Y). The difference is speed — that is, the number of poles. The figures below come from the data sheet; torque is an approximate value from 9550·P/n at the listed speed.

ModelSpeed / polesCurrent (400 V)Approx. torque
DRG-200L1-23000 rpm — 2-pole52.1 A~96 Nm
DRG-200L-41500 rpm — 4-pole53.8 A~191 Nm
DRG-225M-61000 rpm — 6-pole56.2 A~286 Nm

The currents are a guide; when you confirm the thermal overload and contactor in the panel, cross-check them against the motor current chart.

Click to see current electric motor prices and order nowSEE PRICES →

2, 4 or 6 poles: which speed is yours?

The most common slip here is saying "I want 30 kW" and skipping the speed. Yet the same power comes with three different characters:

  • DRG-200L1-2 — 3000 rpm: high speed, lower torque. For fast-running, lighter-torque jobs such as fans, blowers and high-flow centrifugal pumps.
  • DRG-200L-4 — 1500 rpm: the balanced choice and the most requested speed for conveyors, compressors and general drives; the 55x110 mm shaft suits gearbox and coupling connections.
  • DRG-225M-6 — 1000 rpm: low speed, high torque (~286 Nm) for crushers, mixers and hard-starting loads; here the housing steps up a size (225M) with a 60x140 mm shaft.

If you are unsure of the speed, note the pulley/gearbox ratio and the output speed; the electric motor calculator and our team will settle the right pole count with you.

Why cast iron stands out in this class

At 30 kW and above the housing material is a requirement, not a luxury. Cast iron absorbs vibration and stands up better than aluminium to coupling misalignment and shock loads. DRG's cast iron range runs from 0.55 kW to 355 kW, and 30 kW sits in the mid-upper part of that family. Protection is IP55, insulation class F, cooling IC411 — a closed, self-fan-cooled build suited to dusty, damp field conditions.

Connection and voltage: 400/690 V and starting

All three nameplates read 400/690 V (Δ/Y). On a 400 V supply you connect in delta (Δ). At this power most plants use a star-delta or soft starter instead of direct-on-line, to limit inrush current and the shock on the supply. Set the exact starting method from the panel design and the motor nameplate. Connection and commissioning must be done by authorised electrical staff; cut the power and verify isolation before any work.

İzmir-based ready delivery and fast dispatch

DRG Motor's physical site is in İzmir; dispatch goes out from there and reaches every province, İzmir included, by fast carrier or freight. For a standard, widely requested power like 30 kW, models usually move on a ready-to-deliver basis within a short time. Lead time depends on the chosen speed, connection type and delivery address — the cleanest way is to confirm the current situation together when you place the order. Rather than a fixed day promise, we share model availability and the shipping plan at order time.

What to settle before ordering

A wrong unit in heavy industry is costly to undo, so four things settled up front make it easy: power (30 kW), speed (2/4/6 poles), mounting type (foot B3 / flange B5 / B35) and shaft diameter. If you are replacing an existing motor, the quickest route is to photograph its nameplate and send it to us.

Send a photo of your current motor nameplate and we will find the suitable DRG model together.Send on WhatsApp

Click to see current prices for 30 kW three-phase electric motors and start your orderSEE PRICES

You can compare all 30 kW options and other powers in the electric motor shop and pick the best fit for your need, starting with the 30 kW 1500 rpm model.

Frequently asked questions

How many HP is a 30 kW motor?

30 kW is about 40 HP (1 HP ≈ 0.746 kW). The nameplate shows both kW and HP; using the kW figure when ordering avoids confusion.

Why does the same 30 kW have different currents?

Current depends on speed as well as power. At 400 V the 2-pole draws about 52.1 A while the 6-pole draws about 56.2 A. Size the panel protection to the nameplate current of the model you choose.

How do I decide which speed to pick?

Tell us your machine's output speed and drive type (coupling, belt-pulley, gearbox). Based on the speed and torque need, we work out together whether the 2, 4 or 6-pole model suits you.

Electric Motors Related to This Topic — Models and Current Prices

Suitability is not decided by power alone: compare the speed, voltage, mounting, shaft and fixing dimensions of your machine with the product data; if unsure, send us the nameplate of your current motor.

ALL MODELS AND DETAILS IN THE ONLINE SHOP →