The 3 kW three-phase asynchronous electric motor, close to four horsepower, covers the bulk of small and mid-size jobs — and it is one of the ratings DRG Motor keeps most readily to hand. It comes in three speeds (3000, 1500, 1000 rpm), in aluminium and cast-iron housings, dispatched quickly from İzmir to every province of Türkiye.
DRG Motor is a manufacturer, supplier and seller of electric motors. Pick the 3 kW model that fits your need by power and speed in the online electric motor shop, and see the whole range together in the three-phase asynchronous electric motors category.
Why is 3 kW such a commonly requested rating?
How quickly a rating can be supplied depends largely on how standard it is, and 3 kW is comfortably standard. Most machines that go beyond a household load yet do not need a heavy industrial panel land in this band: workshop benches, small booster pumps, extraction fans, mixers, augers. Their common thread is that 3 kW can be used at several different speeds.
In the IEC frame family, 3 kW sits on the 90L, 100L and 132S sizes. Because those frame dimensions are standard, matching is easy; a replacement for an older unit usually lines up on foot and shaft dimensions. A standard frame keeps both fast dispatch and future spares straightforward.
Speed decides the right model
The same 3 kW behaves very differently by pole count. The poles set the speed, and the speed sets the torque you get at the shaft. The rough rule: torque (Nm) = 9550 × power (kW) ÷ speed (rpm). As speed drops, torque rises and current climbs a little.
| Speed | Poles | Torque (approx.) | Current (400 V) |
|---|---|---|---|
| 3000 rpm | 2 | 9.6 Nm | 5.71 A |
| 1500 rpm | 4 | 19.1 Nm | 6.02 A |
| 1000 rpm | 6 | 28.7 Nm | 6.84 A |
For saws, high-speed fans and small compressors, 3000 rpm comes first; for pumps, conveyors and general benches, 1500 rpm; for hard-starting mixers and augers, the 1000 rpm side. Pick the wrong speed and, even with the right power, the machine either strains or spins idle.
Click to see current electric motor prices and order nowSEE PRICES →
Aluminium or cast iron?
At 3 kW you can have either housing; the choice usually follows the mounting spot and duty. An aluminium housing is light and easy to carry or hang — it helps when the unit is removed often or sits up high. Cast iron is heavier and more solid; it is chosen where damping vibration and resisting knocks matter.
If you need a compact solution, there is also a cast-iron option that fits a smaller frame on the 3000 rpm side. Not sure which housing suits you? Describe where it will run and we will settle it together.
Frame size and shaft dimensions
If you are matching a coupling, pulley or gearbox input, shaft diameter and length are what count. The 3 kW models and their dimensions:
| Model | Speed | Housing | Shaft (D×E) |
|---|---|---|---|
| DRG-100L-2-AL | 3000 rpm | aluminium | 28x60 mm |
| DRG-100L2-4-AL | 1500 rpm | aluminium | 28x60 mm |
| DRG-132S-6-AL | 1000 rpm | aluminium | 38x80 mm |
| DRG-100L-2-GG | 3000 rpm | cast iron | 28x60 mm |
| DRG-90L-2K-GG | 3000 rpm (compact) | cast iron | 24x50 mm |
| DRG-100L2-4-GG | 1500 rpm | cast iron | 28x60 mm |
Each model code links straight to its product page, where you can check the mounting type (B3 foot, B5/B14 flange) and the connection detail.
Current at 400 V and the panel side
A 3 kW electric motor draws roughly 6 amps at 400 V; current eases a little at higher speed and rises at lower speed. The thermal relay and contactor are sized from this value. Set the exact figure from the current on the nameplate, and work out the cable cross-section by run length.
For supply and protection, the motor current chart and the cable size calculator help. Leave wiring and measurement to qualified electrical personnel: switch off, confirm the circuit is dead, then work on the panel.
Fast delivery from İzmir
DRG Motor's physical site is in İzmir, and shipping goes out from there. Provinces beyond the Aegean are reached quickly by cargo, so being İzmir-based does not slow delivery down. Confirming which speed and housing is on hand before you order shortens the process.
What to confirm when ordering
The quickest way to avoid the wrong unit is to share a few facts up front: power (3 kW), speed (3000/1500/1000), housing (aluminium/cast iron), mounting type (B3/B5/B14) and shaft diameter. If you are replacing an older unit, the surest method is to photograph its nameplate.
Send a photo of your current motor nameplate and we will find the suitable DRG model together.Send on WhatsApp
See current prices for your 3 kW electric motor and order nowSEE PRICES
Frequently asked questions
How many HP is 3 kW?
About 4 HP. Since one horsepower is roughly 0.75 kW, 3 kW works out to about 4 HP; both figures describe the same electric motor.
Which speed should I choose?
Look at the job's speed: 3000 rpm for fans and saws that must spin fast, 1500 rpm for steady pumps and benches, 1000 rpm for mixers that turn slowly but strongly.
Does the housing material affect delivery?
Both the aluminium and the cast-iron 3 kW models are kept ready; it is enough to confirm which one is on hand at the ordering stage.
Electric Motors Related to This Topic — Models and Current Prices
Suitability is not decided by power alone: compare the speed, voltage, mounting, shaft and fixing dimensions of your machine with the product data; if unsure, send us the nameplate of your current motor.
3 kW Three-Phase Motor 3000 rpm – DRG-100L-2 Aluminium
- 3 kW · 3000 rpm (2 poles)
- Aluminium frame · IEC 100L
- Shaft: 28 × 60 mm
3 kW Three-Phase Motor 1500 rpm – DRG-100L2-4 Aluminium
- 3 kW · 1500 rpm (4 poles)
- Aluminium frame · IEC 100L
- Shaft: 28 × 60 mm
3 kW Three-Phase Motor 1000 rpm – DRG-132S-6 Aluminium
- 3 kW · 1000 rpm (6 poles)
- Aluminium frame · IEC 132S
- Shaft: 38 × 80 mm
3 kW Three-Phase Motor 3000 rpm – DRG-100L-2 Cast Iron
- 3 kW · 3000 rpm (2 poles)
- Cast iron frame · IEC 100L
- Shaft: 28 × 60 mm
3 kW Compact Three-Phase Motor 3000 rpm – DRG-90L-2K Cast Iron
- 3 kW · 3000 rpm (2 poles)
- Cast iron frame · IEC 90L
- Shaft: 24 × 50 mm
3 kW Three-Phase Motor 1500 rpm – DRG-100L2-4 Cast Iron
- 3 kW · 1500 rpm (4 poles)
- Cast iron frame · IEC 100L
- Shaft: 28 × 60 mm
















