The 18.5 kW (about 25 HP) three-phase asynchronous electric motor sits in DRG Motor’s cast-iron, heavy-industry class and is kept ready in three speeds — 3000, 1500 and 1000 rpm. It ships fast from İzmir to every province of Türkiye. At this scale the deciding factor is not the kilowatts but the speed the machine needs, the current on the 400 V side and the starting method chosen in the panel.
DRG Motor is a manufacturer, supplier and seller of electric motors. You can review the three speed options in the 18.5 kW class in the online electric motor shop and see the same family together in the three-phase asynchronous electric motors category.
Where does 18.5 kW show up?
This is the point where you leave the mid range behind and enter the main drives of heavy industry. In the field we meet 18.5 kW most on medium-to-large screw air compressors, hydraulic power packs, high-pressure centrifugal pumps, large radial and scroll fans, crushers and screeners on stone, marble and recycling lines, extruder and injection drives in plastics, flour and feed mills, and heavy conveyor main motors.
What these machines share is the moment of start-up. The load carries real inertia and strains the supply as the motor comes in. So when choosing an 18.5 kW electric motor, "how many kW" is the start of the question, not the end.
Ready dispatch from İzmir: how it runs
DRG Motor is based in İzmir and ships by cargo to all of Türkiye, that city included. Because standard speed options at a common rating like 18.5 kW are kept ready in cast-iron housings, the time between order confirmation and dispatch is short. İstanbul, Bursa, Kocaeli, Gaziantep, Konya or any province of Anatolia — it runs through the same channel.
When a stopped line needs an urgent replacement, time is everything. The most practical move is to photograph the nameplate of the removed electric motor and send it to us; we read the power, speed, housing and shaft size from it and arrange the match quickly. For the main drive of a new machine the same path applies: with the model and province you complete the order in the shop and we plan the fastest route together.
Click to see current electric motor prices and order nowSEE PRICES →
Same power, three characters: speed and torque
With 18.5 kW fixed, torque at the output rises as speed falls and the frame grows. For a rough check T = 9550 · P / n is a guide; the figures below are approximate and a little higher at rated speed.
| Model | Speed | Torque (approx.) | Rated current (400 V) |
|---|---|---|---|
| DRG DRG-160L-2 | 3000 rpm | 59 Nm | 32.5 A |
| DRG DRG-180M-4 | 1500 rpm | 118 Nm | 33.5 A |
| DRG DRG-200L1-6 | 1000 rpm | 177 Nm | 35.9 A |
It reads simply: 2 poles at 3000 rpm give high speed and low torque (fast pumps, compressors); 4 poles at 1500 rpm balance speed and torque, the most requested middle ground; 6 poles at 1000 rpm turn slowly but strongly for hard-starting crushers, mills and mixers. As speed rises the frame grows from 160L through 180M to 200L.
Starting and inrush at 18.5 kW
This is the rating where "should I start it direct?" becomes critical. The 18.5 kW models are wired 400/690 V (delta at 400 V, star at 690 V). On the common 400 V three-phase supply the electric motor runs in delta (Δ). Rated current rises with speed: about 32.5 A at 3000 rpm, 33.5 A at 1500 rpm and 35.9 A at 1000 rpm.
The current drawn at start-up is a multiple of these rated values. If your panel suits direct-on-line, fine; if not, star-delta or a soft starter is a common choice at this class. Which method fits depends on the load inertia, your supply capacity and how often you start. The right call eases both the motor and the supply.
The rated current values are the starting point for thermal relay setting, contactor and cable sizing; always set protection and cross-section to the real value on the motor nameplate. During connection and measurement, cut the power, confirm it is dead and leave the work to authorised electrical staff. Our cable size calculator and motor current chart help at this step.
Cast-iron housing, shaft and mounting
DRG’s aluminium range reaches up to about 11 kW. As 18.5 kW is clearly above that, the housing is cast iron (GG) — not a preference but what the load at this scale requires. Cast iron takes the vibration, heat and shock starts of compressor and crusher lines more solidly and, with its mass, steadies the machine. Protection class is IP55 and insulation is class F.
As the frame grows the shaft diameter changes, which directly affects your coupling, pulley and mounting decision:
| Model | IEC frame | Shaft (D×E) |
|---|---|---|
| DRG DRG-160L-2 | 160L | 42×110 mm |
| DRG DRG-180M-4 | 180M | 48×110 mm |
| DRG DRG-200L1-6 | 200L | 55×110 mm |
So the speed decision is also a mechanical one: will your existing coupling take a 42, 48 or 55 mm shaft, and is the machine footed (B3) or flanged (B5)? Settling this before ordering prevents the wrong shaft diameter reaching the field.
Four points to confirm when ordering
Four pieces of information are enough to pin down the right 18.5 kW electric motor quickly and without error:
- Speed: the speed your machine needs — 3000, 1500 or 1000 rpm.
- Mounting and shaft: foot (B3), flange (B5) or combined; a 42×110, 48×110 or 55×110 mm shaft.
- Voltage: your site supply (commonly 400 V three-phase → delta connection).
- Starting: whether the panel uses direct, star-delta or a soft starter.
If you are unsure about the speed or housing, just describe your application in a few words and we settle the right model together. For a first idea you can also check our electric motor calculator.
Send a photo of your current motor nameplate and we will find the suitable DRG model together.Send on WhatsApp
See the current options and prices for your 18.5 kW electric motor in the shop.SEE PRICES
Frequently asked questions
How many HP is 18.5 kW?
18.5 kW is about 25 HP (1 HP ≈ 0.746 kW). Buyers looking for a "25 HP electric motor" are usually pointed to this power class too.
Should 18.5 kW be started direct-on-line?
There is no fixed recipe; it depends on your panel and supply. Besides direct starting, star-delta and soft starters are common at this class. Load inertia and start frequency are decisive; make the call with authorised electrical staff.
Which speed comes in which frame?
160L for 3000 rpm, 180M for 1500 rpm and 200L for 1000 rpm. As speed falls the frame and shaft grow, so the speed decision should be considered together with the mounting.
Which provinces do you deliver to?
DRG Motor is based in İzmir and ships by cargo to all of Türkiye, İzmir included. For a firm dispatch plan, just send us your model and province.
Electric Motors Related to This Topic — Models and Current Prices
Suitability is not decided by power alone: compare the speed, voltage, mounting, shaft and fixing dimensions of your machine with the product data; if unsure, send us the nameplate of your current motor.
18.5 kW Three-Phase Motor 3000 rpm – DRG-160L-2 Cast Iron
- 18.5 kW · 3000 rpm (2 poles)
- Cast iron frame · IEC 160L
- Shaft: 42 × 110 mm
18.5 kW Three-Phase Motor 1500 rpm – DRG-180M-4 Cast Iron
- 18.5 kW · 1500 rpm (4 poles)
- Cast iron frame · IEC 180M
- Shaft: 48 × 110 mm
18.5 kW Three-Phase Motor 1000 rpm – DRG-200L1-6 Cast Iron
- 18.5 kW · 1000 rpm (6 poles)
- Cast iron frame · IEC 200L
- Shaft: 55 × 110 mm













