If you need an 18.5 kW electric motor and cannot afford to wait, two things have to be clear at once: the right speed-and-housing match, and when the shipment actually leaves. DRG Motor keeps this power class ready in three different speeds and ships fast from its İzmir base to every province in Türkiye.

18.5 kW cast-iron grey DRG three-phase asynchronous electric motor

DRG Motor is a manufacturer, supplier and seller of electric motors. You can review the 18.5 kW cast-iron models by power and speed in the online electric motor shop and see the whole family together in the three-phase asynchronous electric motors category.

What does 18.5 kW handle?

This rating sits above the light-bench class, right in the middle of heavy work. In the field we most often see an 18.5 kW electric motor on jaw crushers, long belt conveyors, screw and piston air compressors, high-flow centrifugal pumps, exhaust and body fans, flour and feed mills, and hydraulic power units.

They share one trait: the load is either continuously heavy or hard at start-up. Sizing the power too tight on such a load overheats the electric motor and trips the thermal often; sizing it too large stresses the panel needlessly at start-up. 18.5 kW is the step that mid-to-heavy industry reaches for between those two extremes.

Same power, three characters

The figure 18.5 kW alone does not finish an order. The real difference comes from the number of poles, that is, the speed. All three options give the same power, yet the character at the shaft is completely different:

ModelSpeedCurrent (400 V)Shaft
DRG-160L-23000 rpm (2-pole)32.5 A42x110 mm
DRG-180M-41500 rpm (4-pole)33.5 A48x110 mm
DRG-200L1-61000 rpm (6-pole)35.9 A55x110 mm

The fast 2-pole model usually goes on compressors and high-flow pumps; the balanced 4-pole on conveyors, fans and most general drives; the slow, high-torque 6-pole on mills, mixers and hard-starting machines. One thing to watch: as speed drops the frame grows. The table shows it — the 2-pole arrives in a 160 frame while the 6-pole climbs to a 200 frame. That directly affects your mounting holes and shaft diameter.

Click to see current electric motor prices and order nowSEE PRICES →

Why a cast-iron housing?

At this rating a cast-iron housing earns its keep. Cast iron is heavy, but it absorbs vibration and takes shock and heat in stride. On crushers, mills and compressors that load suddenly, that toughness is not wasted; it keeps coupling and pulley alignment true for longer. That is why DRG's 18.5 kW family comes with a cast-iron housing, IP55 protection and class F insulation.

Current and starting

At 400 V the rated current of an 18.5 kW electric motor runs roughly in the 32–36 A band, depending on speed. The point is not the rated figure but the moment of start-up: an asynchronous electric motor draws several times its rated current on first movement. That is why direct-on-line starting is uncomfortable on many panels at this power.

The 400/690 V (Δ/Y) connection on the nameplate allows star-delta starting; at this rating many plants choose a soft starter or a drive. Which method suits you depends on your panel and load. When sizing cable and protection, the motor current chart and the cable size calculator point the way. Let qualified electrical personnel make the connection; cut the power and verify it is dead before starting.

How fast delivery and supply work

DRG Motor is based in İzmir and ships fast to the whole of Türkiye, that city included. What speeds up supply is not complicated: settle from the start which speed, which housing, which mounting type and which shaft diameter you want. Once those four are clear, the shipment leaves quickly.

To make it faster still, photograph the nameplate of your old electric motor and send it over. We compare the values and confirm the best-fit model from the 18.5 kW family with you.

Four things to settle when ordering

State these four on the phone or in writing and the choice lands first time: speed (2/4/6-pole), mounting type (foot B3, flange B5 or B35), shaft diameter and your plant's line voltage. Where you are unsure, a photo of the machine's current connection speeds everything up. You can see all 18.5 kW options side by side in the online electric motor shop.

Click to see the current price of your 18.5 kW electric motor and start your orderSEE PRICES

Frequently asked questions

Which speed should I pick for 18.5 kW?

Look at the machine doing the work. Compressors and high-flow pumps usually want 3000 rpm; conveyors, fans and general drives are happy at 1500 rpm; mills and hard-starting loads lean to 1000 rpm. If unsure, describe the machine and we choose together.

Should I start it direct-on-line at this power?

At 18.5 kW most plants avoid direct starting; the inrush current is high. The Δ/Y connection on the nameplate allows star-delta, and a soft starter or drive is a common choice too. The decision depends on your panel and load.

How long does delivery take?

DRG Motor ships fast from its İzmir base to all of Türkiye. Once you settle speed, housing and mounting type up front, the shipment starts quickly; we confirm the exact time together at order.

Send a photo of your current motor nameplate and we will find the suitable DRG model together.Send on WhatsApp

Electric Motors Related to This Topic — Models and Current Prices

Suitability is not decided by power alone: compare the speed, voltage, mounting, shaft and fixing dimensions of your machine with the product data; if unsure, send us the nameplate of your current motor.

ALL MODELS AND DETAILS IN THE ONLINE SHOP →