When choosing a new motor to replace a flange-mounted (B5) WEG W22 electric motor, what decides the outcome is the surface and the spigot by which the motor attaches to the machine. A foot-mounted motor's base can offer some tolerance; on a flange motor the spigot diameter, the bolt circle and the shaft end must all match at once. This article explains which flange and shaft dimensions to take on your W22 B5 motor and how to pass them to DRG MOTOR.

Grey three-phase electric motor with DRG MOTOR logo – flange and shaft check for a WEG W22 B5 replacement

FF flange and B5 mounting on the W22

According to WEG's European catalogue, the FF-type (through-hole) flange is offered on all W22 frames; mountings such as B5, B35 and V1 use this flange. The catalogue assigns flange size to frame as follows: FF-165 for 80–90, FF-215 for 100–112, FF-265 for 132, FF-300 for 160–180 and FF-350 for 200. The small C-DIN (B14) flange is listed only up to frame 132; if your motor's flange has tapped holes, that is a different case outside the scope of this article.

One point to note: an older WEG catalogue (African market, 2020) gives FF-300 for frame 132 and FF-350 for 160. The current European catalogue shows FF-265 and FF-300. Determine which flange your motor has by measuring, not from a catalogue number.

Values to measure on the flange

  • M – bolt circle diameter: between the centres of two opposite fixing holes.
  • N – spigot (pilot) diameter: diameter of the register that locates in the machine; the most critical dimension.
  • P – flange outside diameter: matters for fitting the recess and nearby parts.
  • S – hole diameter and number of holes.
  • T – spigot depth and LA – flange thickness.

Measure the spigot diameter with a caliper at several points; clean off paint or corrosion first. Also measuring the mating recess on the machine side allows compatibility to be checked from both sides.

Shaft end: diameter, length and key

On B5 motors the shaft often goes directly into a pump, a fan hub or a coupling half, so shaft length (E) and key size can be more critical than with foot mounting. The W22 IE3 catalogue gives the shaft as 28j6×60 for 112M, 38k6×80 for 132 and 42k6×110 mm for 160M. Also note the tapped centre hole at the shaft end (if any) and the keyway width.

The same kW and the same speed class alone do not show that the flange will seat: for example, the 4-pole 11 kW W22 IE3 motor is listed in a 160M frame, for which the catalogue gives the FF-300 flange, while the 4-pole 7.5 kW motor is listed in 132S/M and frame 132 takes FF-265. One step in output can change both flange and shaft.

Send your measured M, N, P, S values and shaft dimensions with the plate photo to DRG MOTOR; flange and shaft compatibility can be examined with these data.

Comparison with DRG B5 flange dimensions

The DRG catalogue's large B5 flange dimensions are shown below next to the FF designation from the W22 European catalogue. The table is a starting point; suitability is only established with dimensions measured on site.

FrameW22 FF flange (EU catalogue)DRG B5 flange M / N / P (mm)DRG shaft D×E (mm)
112MFF-215215 / 180 / 25028×60
132S/MFF-265265 / 230 / 30038×80
160MFF-300300 / 250 / 35042×110

Example DRG models that can be evaluated: DRG-112M-4 (4 kW, 112M), DRG-132M-4 (7.5 kW, 132M) and DRG-160M-4 (11 kW, 160M). These models are also offered in B5 mounting; up to 11 kW aluminium and cast iron housings are available, while the W22 is cast iron on all frames. The full range is in the DRG MOTOR online shop, general application motors on the general purpose motors page. Drawings can be reviewed in the DRG technical drawings.

Questions on replacing a flanged W22

The bolt circle matches but the spigot diameter differs; what then?

With a different spigot diameter, the motor may not locate correctly on the axis. Solutions such as an adapter flange must then be assessed on the machine side; no firm decision can be made before dimensions and machine design are reviewed.

My motor runs vertically (V1); are B5 dimensions enough?

The flange dimensions stay the same, but with vertical mounting the axial load on the shaft, rain/water ingress and fan cover orientation also matter. Always state the mounting orientation and the load.

Can I rely on the flange size from an older catalogue?

Since catalogues differ, measuring on the motor itself is the right approach.

What to send to DRG MOTOR

  • Photo of the W22 nameplate (frame, kW, speed, voltage, mounting data)
  • Flange dimensions: M, N, P, S and number of holes; T and LA if possible
  • Shaft diameter×length, key width and shaft-end thread data
  • Mounting orientation (horizontal B5 or vertical V1) and the equipment attached to the motor
  • Photo of the mating flange or recess on the machine
  • Operating hours, starting conditions and ambient conditions

DRG Motor is a manufacturer, supplier and seller of electric motors. Send the flange and shaft dimensions with the plate photo and machine data; a suitable flanged option will be evaluated with these data. You can write via WhatsApp, use the quote list, call +90 (542) 666 11 11 or e-mail info@drgmotor.com (contact page).

See current prices of DRG MOTOR electric motors and order online in our storeSEE PRICES →

Technical Sources

  • WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — 18 Mechanical Data: Flange Mounted Motors, FF and C-DIN flange tables — PDF page 76 (printed page 76).
  • WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — 6 Mounting Forms: mounting table (IM B5, IM V1, IM B35) — PDF page 18 (printed page 18).
  • WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — 17 Electrical Data: W22 Premium Efficiency IE3 (50Hz) 4-pole table — PDF page 41 (printed page 41).
  • WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — 18 Mechanical Data: shaft end dimensions (D×E) — PDF page 71 (printed page 71).
  • WEG — W22 Three-Phase Electric Motor Technical Catalogue, African Market (Cod 50024206) — Rev 21, 11/2020 — Flange Mounted Motors: FF flange table — PDF page 76 (printed page 76).