If you are replacing a WEG W22 electric motor that sits on the input side of a gearbox with a small face flange, the key question is not power but how the flange, the shaft and the gearbox input will meet the new motor. This article explains how to confirm that your motor really is B14, which dimensions to take on the gearbox side, and what information to send to DRG MOTOR so that an option can be assessed on technical data.
First confirm that the motor really is B14
According to WEG's W22 technical catalogue for the European market, B14 and B34 mountings are offered with a C-DIN flange to EN 50347 and only up to frame 132. For frames 160 and above, B14 with a C-DIN flange is not defined; for these frames the catalogue shows the FF flange (FF-300 for frames 160–180) and, as an option, a C flange to NEMA MG 1 Part 4. So if the frame field on your nameplate reads 160 or 180 and the motor is flanged to a gearbox, the connection is not a C-DIN B14; which flange type it is can only be established by measuring.
The small-flange assignment in the catalogue is as follows:
| Frame (nameplate field) | W22 C-DIN flange designation |
|---|---|
| 63 | C-90 |
| 71 | C-105 |
| 80 | C-120 |
| 90 | C-140 |
| 100–112 | C-160 |
| 132 | C-200 |
On a B14 flange the fixing holes are usually tapped and the bolts come in from the gearbox side; on a B5 flange the holes are clearance holes and the flange is larger than the housing. This simple observation tells you which group you are in even before removing the motor.
Which dimensions to take on the gearbox side
A motor catalogue does not contain information specific to your gearbox connection; you take these measurements on site. In general, check:
- Spigot (pilot) diameter and depth of the gearbox input flange
- Pitch circle, number and thread size of the fixing holes
- Shaft diameter, shaft length and key width entering the gearbox input bore
- Any intermediate coupling, shaft sleeve or IEC adapter
- Motor position relative to the gearbox: horizontal, or vertical shaft down or up
If the shaft is too short the key does not seat fully; if it is too long the shaft may bottom out inside the gearbox. A small difference in spigot diameter can stop the flange from seating at all. That is why the word "B14" alone is not a sufficient description; different flange sizes can be used on the same shaft height.
Why power and speed come right after
The gearbox output speed depends on the motor's rated speed and the gear ratio. The W22 catalogue gives a full-load speed of 1465 rpm for the 4-pole 7.5 kW IE3 motor; if the new motor's speed differs noticeably, the machine's output speed changes too. At the same time, matching kW and speed class is not enough: in the W22 catalogue the 4-pole 5.5 kW motor is in frame 132S/M with a 38k6x80 shaft. A smaller housing at the same power, for example a compact motor in frame 112M with a 28×60 mm shaft, means a different shaft and a different flange; it cannot be considered suitable for the gearbox input until the dimensions are compared.
Pass your flange and shaft measurements to DRG MOTOR along with photos of the motor and gearbox nameplates, so that an option can be assessed with those dimensions side by side.
Options that can be assessed on the DRG MOTOR side
DRG Motor is a manufacturer, supplier and seller of electric motors. Besides B3, B5 and B35 mounting, the DRG range also includes a B14 option; however, B14 flange dimensions are not given here and are confirmed with the order. This assessment covers the selection of the electric motor to be connected to the existing equipment; the flange and shaft dimensions of your existing gearbox are the basis of the comparison. If your motor has a brake, a separate fan or a drive integrated into the motor, mention this as well; these features change the assessment. You can also look at the Electric Motors for Gearboxes page. Models whose dimensions can be compared with W22 B14 electric motors up to frame 132 include:
- DRG-100L2-4: IEC frame 100L, 28×60 mm shaft, 8 mm key; 3 kW, 1500 rpm class (1450 rpm)
- DRG-112M-4: IEC frame 112M, 28×60 mm shaft, 8 mm key; 4 kW, 1500 rpm class (1450 rpm)
- DRG-132M-4: IEC frame 132M, 38×80 mm shaft, 10 mm key; 7.5 kW, 1500 rpm class (1460 rpm)
These models do not imply definite suitability; shaft and frame dimensions should be checked against the technical drawings, and the flange size confirmed with the order. Any change to the connection or protection arrangement should be assessed by competent technical staff.
Frequently asked questions
My W22 motor is frame 160 and flanged to a gearbox. Is it B14?
In the catalogue, B14 with a C-DIN flange is defined for the W22 only up to frame 132. On frame 160 it may be an FF flange or, as an option, a NEMA C flange; the type cannot be identified without measuring the flange outer diameter, pitch circle and spigot diameter.
Will a DRG motor fit my existing gearbox?
That cannot be known without comparing flange and shaft dimensions. Since B14 flange dimensions are confirmed with the order, your own measurements are needed first.
Do I need to replace the gearbox as well?
That is a separate decision from the motor replacement. If the gearbox shows noise, oil leaks or backlash, its condition should be assessed by competent staff. If the gearbox is also being renewed, say so in your request; the motor dimensions are then compared against the new gearbox.
The nameplate says IE3; should I send that too?
Yes. The efficiency class on the nameplate can help explain differences in housing length; send it together with the other nameplate data.
Checklist for a gearbox application
- Photo of the nameplate (motor code, frame, power and speed fields readable)
- Mounting type: B14, B34, or a photo of the flange if you are unsure
- Flange dimensions: spigot diameter, pitch circle, number of holes and thread size
- Shaft diameter, shaft length and key width
- Gearbox nameplate photo and ratio
- Motor position (horizontal, vertical shaft down, vertical shaft up)
- Driven machine and daily operating hours
- Supply voltage and frequency
With this information, a suitable option is assessed by reviewing the technical data and the machine's operating conditions together.
You can send this information via WhatsApp, by phone on +90 (542) 666 11 11, by e-mail to info@drgmotor.com or through the contact page. You can also add the models you are looking at to the quote list, and browse the full range on the buy electric motors online page.
See current prices of DRG MOTOR electric motors and order online in our storeSEE PRICES →
Technical Sources
- WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — Section 6 Mounting Forms (B14/B34 C-DIN flange note) — printed page 18.
- WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — W22 IE3 50 Hz electrical data, IV-pole table — printed page 41.
- WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — Section 18 Mechanical Data (shaft end dimensions) — printed page 71.
- WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — Flange Mounted Motors: FF and C-DIN flange tables — printed page 76.










