The difference between IP54 and IP55 is in the second digit: both are dust protected (first digit 5), but against water IP54 only resists splashing water, while IP55 resists low-pressure water jets from any direction (hose/jet). So IP55 is one step further on the water side. DRG three-phase asynchronous motors are rated IP55 as standard.

Grey DRG three-phase asynchronous electric motor representing the IP55 protection class

DRG Motor is a manufacturer, supplier and seller of electric motors. You can see every IP55-protected three-phase model by power and speed in the online motor shop, and view the same motors together in the three-phase asynchronous electric motors category.

What does the IP code mean?

IP stands for "Ingress Protection" and describes a device's degree of protection against external influences with two digits. Each of the two digits after the letters "IP" has its own meaning:

  • First digit (0–6): protection against solid objects and dust. The higher it is, the smaller the particles kept out; 5 means dust protected and 6 means fully dust tight.
  • Second digit (0–9): protection against water. 4 is splashing water, 5 is low-pressure water jets, 6 is powerful water jets.

So if a motor nameplate reads "IP55", the first 5 covers dust and the second 5 covers water jets. Reading the digits one by one is the most practical way to compare two protection classes.

What does IP54 mean?

In IP54 the first digit 5 means the motor is dust protected, and the second digit 4 means it is protected against splashing water from any direction. Dust is not fully excluded but cannot enter in amounts that disturb operation. On the water side, dripping and splashing are safe; directing pressurised water at it is outside the IP54 scope. This level is intended for indoor, dusty but non-washed areas.

What does IP55 mean?

In IP55 the first digit is again 5, so dust protection is the same as IP54. The difference is the second digit: 5 shows the motor is protected against low-pressure water jets from any direction, such as hose cleaning. IP55 therefore offers a wider safety margin where contact with water is more likely. The standard protection class of DRG three-phase asynchronous motors is IP55.

IP54 versus IP55 in one table

The shared and differing points of the two classes are shown below. Dust protection is identical; the distinction is only in water resistance.

FeatureIP54IP55
First digit (solids / dust)5 — dust protected5 — dust protected
Second digit (water)4 — against splashing water from any direction5 — against low-pressure water jets from any direction
Water resistanceSplashing waterHose/jet water spray
Typical environmentIndoor, dusty but not washed-down areasAreas more exposed to wash-down and weather

In short: on dust IP54 and IP55 are equal, on water IP55 is one step ahead. The answer to "which is better?" is not absolute; the right class is decided by the environment in which the motor will run.

Click to see current electric motor prices and order nowSEE PRICES →

Where is IP54 or IP55 preferred?

The protection-class choice depends on the dust and water conditions the motor faces:

  • IP54 can be enough: indoor, relatively clean or merely dusty areas; interiors where splashing is rare and no wash-down is carried out.
  • IP55 is more suitable: production lines cleaned with a hose, humid environments, conveyor and pump applications exposed to spray, and points more exposed to the weather.

If your application involves regular wash-down, humidity or water spray, the IP55 class fits the need better. DRG motors being IP55 aims to cover this wider range of use as standard. For much harsher water/dust conditions (such as continuous immersion), it is best to assess the application separately within this general IP framework.

IP55-protected DRG three-phase asynchronous motor models

The table below lists some 4-pole (1500 rpm class) DRG models as examples; all are rated IP55 and the model codes link straight to the product page. Aluminium and cast iron housing options are offered with identical electrical figures.

ModelPower and speedHousingProtection class
DRG-100L2-4-AL (aluminium)3 kW · 1500 rpmaluminiumIP55
DRG-132S-4-AL (aluminium)5.5 kW · 1500 rpmaluminiumIP55
DRG-112M-4K-AL (aluminium)5.5 kW · 1500 rpmaluminiumIP55
DRG-132M-4-AL (aluminium)7.5 kW · 1500 rpmaluminiumIP55
DRG-100L2-4-GG (cast iron)3 kW · 1500 rpmcast ironIP55
DRG-132S-4-GG (cast iron)5.5 kW · 1500 rpmcast ironIP55

These models show how IP55 protection combines with power and housing options. For other speed classes (2 and 6 poles) and power steps, see the full list on the shop page.

Points to watch when reading a protection class

An IP value makes sense together with the motor's installation and operating conditions. Proper closing of the terminal box, use of glands/seals, and tight cable entries matter for keeping the stated class in the field. Before any electrical work, switch off the supply, confirm it is de-energised, and let only qualified electrical personnel make the connection. For the exact protection class and wiring details, always refer to the motor nameplate and the device documentation.

Send a photo of your current motor nameplate and we will find the suitable DRG model together.Send on WhatsApp

Let us determine the right protection class and model together, based on the dust and water conditions in your environment.

See the IP55-protected three-phase asynchronous DRG models and current options in the shopSEE PRICES

Frequently asked questions

What is the main difference between IP54 and IP55?

Dust protection is the same in both (first digit 5). The difference is the second digit: IP54 protects against splashing water, IP55 against low-pressure water jets from any direction. So IP55 is one step further on the water side.

What is the protection class of DRG motors?

DRG three-phase asynchronous motors are rated IP55 as standard. The exact protection information is always stated on the relevant model's nameplate and product page.

Is an IP55 motor fully waterproof?

No. IP55 protects against low-pressure water jets; it is not designed for continuous immersion or high-pressure jets. Where water contact is very heavy, the application should be assessed separately.

How is an IP protection class read?

The first digit after "IP" describes dust protection and the second water protection. For example, in IP55 the first 5 means dust protected and the second 5 means resistant to water jets.

Electric Motors Related to This Topic — Models and Current Prices

Suitability is not decided by power alone: compare the speed, voltage, mounting, shaft and fixing dimensions of your machine with the product data; if unsure, send us the nameplate of your current motor.

ALL MODELS AND DETAILS IN THE ONLINE SHOP →