If the WEG W22 electric motor in your plant needs to be renewed, the first question is usually "Which motor can replace it?". The answer does not come from the motor's name; it comes from the values on its nameplate, its mounting dimensions and the way the machine works. This article helps you identify your W22 motor correctly, know which points to compare, and gather the information needed for a DRG MOTOR option to be evaluated on technical data.
Identify the motor first: what is on a W22 nameplate?
W22 is WEG's IEC low-voltage three-phase motor series; the European catalogue lists it in IE3, IE4 and IE5 efficiency versions, in frames from 63 up to 355A/B. Two WEG W22 electric motors sharing the series name are not necessarily the same size, so the evaluation starts with the nameplate.
According to the manufacturer's catalogue, the nameplate shows a numeric "motor code", frame size, full-load speed (rpm), rated output, voltage, frequency, rated current, power factor, IP rating, insulation class, ambient temperature, altitude, bearing types and the connection diagram, among other fields. Frame size and full-load speed appear in separate fields on the plate; the number of poles is read from the speed. A sharp, glare-free photo of the nameplate is therefore the most useful document. If the plate says IE3 or IE4, pass that on as well; it is only needed to describe the existing motor.
Three axes of comparison: frame, mounting, voltage
The W22 catalogue states that output-to-frame assignment follows EN 50347 and IEC 60072-1, and mounting arrangements are defined with IEC 60034-7 codes (B3, B5, B35, B14, V1 and so on). This makes comparison with another IEC-frame motor possible, but it is not enough by itself:
- Frame and shaft: compare the frame code on the plate (e.g. 112M, 132S/M, 160M) and measure shaft diameter × length and key width on site.
- Mounting: the standard W22 build is foot-mounted B3T; flange and foot-and-flange versions have their own dimension tables. Measure the flange type and its diameters.
- Voltage: in the standard design of WEG's European catalogue, 220-240/380-415 V is given up to 100L and 380-415/660 V from 112M upwards. In the DRG MOTOR online shop, models up to 3 kW are listed at 230/400 V and models of 4 kW and above at 400/690 V; any special voltage or different frequency must be stated separately. Whether the motor suits the existing supply must be determined by checking the nameplate voltage, frequency, manufacturer tolerances and connection arrangement together. Whether the connection arrangement must change should be decided by qualified technical staff.
Matching the kW rating or the speed class alone is not sufficient: a 7.5 kW W22 IE3 motor, for example, is listed in a 132S frame with 2 poles and in a 160M frame with 6 poles. Two motors of the same output can have different shafts and foot spacing.
If you send the nameplate photo and the dimensions you measured to DRG MOTOR now, a suitable option can be examined technically together with your machine data.
Housing material and long "L" frames
The catalogue gives every W22 frame from 63 to 355A/B in FC-200 cast iron. In the DRG MOTOR range, cast iron housings cover 0.55–355 kW and aluminium housings cover 0.25–11 kW. For a replacement up to 11 kW both materials can be evaluated; vibration, environment and the mounting surface influence the choice.
In the W22 IE3 and IE4 tables some outputs are listed with an "L"-prefixed frame (e.g. L100L, L132S). In the catalogue's dimension table, for example, L100L has the same shaft height as 100L (H=100 mm) but a longer overall length (418 mm instead of 376 mm). So if you see a code such as "L100L" on the plate, measure the overall motor length and the free space between the fan cover and the machine as well.
DRG options that can be evaluated
The models below are examples only; suitability becomes clear after dimensions and operating conditions are compared. See the DRG electric motor shop for the full range and the general purpose electric motors page for general applications.
- DRG-112M-4: 4 kW, frame 112M, rated speed 1450 rpm, 400/690 V, shaft 28×60 mm.
- DRG-132M-4: 7.5 kW, frame 132M, rated speed 1460 rpm, 400/690 V, shaft 38×80 mm.
- DRG-160M-4: 11 kW, frame 160M, rated speed 1465 rpm, 400/690 V, shaft 42×110 mm.
The motor current chart can help when comparing the plate current with DRG data.
Questions about replacing a W22
How do I identify the motor if there is no type code?
The W22 plate shows a numeric motor code plus separate fields for frame and speed. A photo of these fields and your measured shaft and mounting dimensions are usually a sufficient starting point; if something is missing, further measurements may be requested.
Does the same frame code settle everything?
No. The frame code is an important indicator, but long "L" frames, flange type, terminal box position and coupling distance must be checked separately.
My motor failed; must the new one have the same output?
First the cause of the failure should be investigated. With overload, frequent starts, moisture or misalignment, a motor of the same output may meet the same problem. The machine's load and operating time determine the output decision.
Can an aluminium housing be chosen instead of cast iron?
Aluminium housings up to 11 kW are available in the DRG range. Whether this fits depends on the mounting arrangement, vibration and ambient conditions; the decision should be made together with dimensions and usage data.
Information to send to DRG MOTOR
- A legible photo of the W22 nameplate (motor code, frame, speed, voltage and current fields visible)
- kW, speed and frequency from the plate
- Mounting arrangement (foot, flange, foot-and-flange) and whether the frame code has an "L" prefix
- Shaft diameter, shaft length and key width
- Foot hole spacing or flange diameters
- The driven machine, the drive type (coupling, pulley, gearbox) and daily operating hours
- Ambient conditions and any failure history
DRG Motor is a manufacturer, supplier and seller of electric motors. Put this information together and send it; the option will be evaluated by reviewing your motor's technical data and the machine's operating conditions together. You can write via WhatsApp, use the quote list, call +90 (542) 666 11 11 or e-mail info@drgmotor.com (contact page).
See current prices of DRG MOTOR electric motors and order online in our storeSEE PRICES →
Technical Sources
- WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — 1 Versions Available: IE3, IE4 and IE5 versions, EN 50347 output–frame assignment — PDF page 8 (printed page 8).
- WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — 3.11 Nameplate: list of nameplate fields — PDF page 11–12 (printed page 11–12).
- WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — 6 Mounting Forms: B3L, B3T, B3R terminal box positions and mounting table — PDF page 17–18 (printed page 17–18).
- WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — 15 Construction Features: B3T mounting, FC-200 cast iron frame, voltage and frequency — PDF page 24 (printed page 24).
- WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — 17 Electrical Data: W22 Premium Efficiency IE3 (50Hz) 2, 4 and 6-pole tables — PDF page 40–42 (printed page 40–42).
- WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — 18 Mechanical Data: Foot Mounted Motors dimension table (H and overall length L) — PDF page 72 (printed page 72).










