If you are preparing to renew a WEG W22 electric motor whose nameplate reads "W22 IE3", the efficiency class stands out, but on its own it does not show whether a motor fits the machine mechanically and electrically. Whether a new motor fits the machine is shown by frame length, shaft, speed, current and connection data. This article walks you through which fields to read on a W22 IE3 plate, which dimensions to take and which data to send to DRG MOTOR.

What the IE3 marking tells you, and what it does not

In WEG's European catalogue, W22 IE3 is defined as the "Premium Efficiency" version according to IEC 60034-30-1:2014, and it appears on the plate in a separate "Efficiency Code – IE" field. It tells you which version your motor is; it says nothing about shaft diameter, foot spacing or flange. Photograph the whole plate including the IE field, and pass on the IE data only as a description of the existing motor.

Grey three-phase electric motor with DRG MOTOR logo – technical checks for a WEG W22 IE3 replacement

Technical fields to read on the nameplate

Following the numbering in the catalogue, these W22 plate fields matter most for a replacement:

  • Frame size: such as 100L, 112M, 132S/M; note separately if it starts with "L".
  • Full-load speed (rpm): shows the number of poles; e.g. 1465 rpm indicates a 4-pole motor.
  • Voltage and frequency: 220-240/380-415 V or 380-415/660 V, 50 or 60 Hz.
  • Rated current and power factor: used when reviewing the existing protection settings.
  • Ambient temperature, altitude and service factor: show the conditions the motor is rated for.
  • Connection diagram and duty type: send the duty type information from the plate too.
  • Front/rear bearing types: for the record only; the new motor's bearings are assessed from its own data.

Length check on IE3 frames with an "L" prefix

In the W22 IE3 tables some outputs are listed with an "L"-prefixed frame that is longer than the standard one. For example, the 4-pole 3 kW IE3 motor is listed in frame L100L with a 28j6×60 mm shaft. In the catalogue's dimension table, L100L has the same shaft height as 100L (H=100 mm) but an overall length of 418 mm instead of 376 mm.

So even when shaft height and shaft size match, the overall length may differ. Check the space behind the fan cover, the terminal box position and the cable length. As an example, DRG-100L2-4 is listed with 3 kW, frame 100L, rated speed 1450 rpm, shaft 28×60 mm and overall length (L) 406 mm; measure your existing motor and compare it with this value.

Send the length you measured, along with shaft and mounting dimensions, to DRG MOTOR so suitability can be examined with these data.

Beyond the plate values: load and operating conditions

Two motors can share the same output and speed class and still not be interchangeable. The 4-pole 5.5 kW WEG W22 IE3 electric motor is listed in a 132S/M frame with a 38k6×80 mm shaft; a motor of the same output with a different frame length may not fit the machine because of foot holes or coupling distance. The starting load, frequent stop-starts, inverter operation and dust, humidity and temperature of the site also affect the choice. The DRG range is specified for IP55, class F insulation, −15…+40 °C ambient and altitudes up to 1000 m; mention it if the ambient and altitude on your plate differ.

DRG models that can be compared on technical data

The models below are example options; suitability becomes clear after a dimension comparison. The full range is in the DRG MOTOR shop, general-use options on the general purpose motors page. For the dimension check you can also use the DRG technical drawings.

  • DRG-100L2-4: 3 kW, 100L, 1450 rpm, 230/400 V.
  • DRG-112M-4: 4 kW, 112M, 1450 rpm, 400/690 V, shaft 28×60 mm.
  • DRG-132S-4: 5.5 kW, 132S, 1460 rpm, 400/690 V, shaft 38×80 mm.

On voltage: in the standard design of WEG's European catalogue, 220-240/380-415 V is given up to 100L and 380-415/660 V from 112M upwards. In the DRG MOTOR online shop, models up to 3 kW are listed at 230/400 V and models of 4 kW and above at 400/690 V; any special voltage or different frequency must be stated separately. Whether the motor suits the existing supply must be determined by checking the nameplate voltage, frequency, manufacturer tolerances and connection arrangement together. Decisions on connection and protection belong to qualified technical staff.

Common questions on IE3-labelled W22 motors

Should I only look at the IE class when replacing my IE3 motor?

No. The IE data describes the existing motor; mechanical and electrical suitability is determined by frame, shaft, mounting, voltage and operating conditions. If an efficiency class is required for the new motor by the specification, the project conditions or applicable regulations, the selection must also meet that requirement. Mechanical and electrical suitability checks do not replace this requirement.

My plate says "L100L"; is it the same as a normal 100L?

The shaft height is the same (100 mm), but in the catalogue's dimension table L100L is longer overall than 100L. So you need to measure the overall length.

Must the plate current equal the new motor's current?

Current values differ from motor to motor. Protection settings may need to be reviewed for the new motor; this assessment should be made by qualified technical staff.

Data to send to DRG MOTOR

  • A full photo of the W22 nameplate including the IE field
  • Frame code (with any "L" prefix) and full-load speed
  • Voltage, frequency, rated current and power factor
  • Overall motor length, shaft diameter×length and key width
  • Mounting arrangement and foot/flange dimensions
  • Machine type, starting condition, inverter use and daily operating hours
  • Ambient temperature, altitude, dust and humidity

DRG Motor is a manufacturer, supplier and seller of electric motors. Once you send the listed data, the option is evaluated by setting the plate values side by side with your machine's operating conditions. You can write via WhatsApp, use the quote list, call +90 (542) 666 11 11 or e-mail info@drgmotor.com (contact page).

See current prices of DRG MOTOR electric motors and order online in our storeSEE PRICES →

Technical Sources

  • WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — 1 Versions Available: IE3, IE4 and IE5 versions, EN 50347 output–frame assignment — PDF page 8 (printed page 8).
  • WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — 3.11 Nameplate: list of nameplate fields — PDF page 11–12 (printed page 11–12).
  • WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — 15 Construction Features: B3T mounting, FC-200 cast iron frame, voltage and frequency — PDF page 24 (printed page 24).
  • WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — 17 Electrical Data: W22 Premium Efficiency IE3 (50Hz) 4-pole table — PDF page 41 (printed page 41).
  • WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — 18 Mechanical Data: Foot Mounted Motors dimension tables (shaft, overall length L) — PDF page 71–72 (printed page 71–72).