When renewing a 7.5 kW WEG W22 electric motor, the most common mistake is to search for "7.5 kW" alone. At this output the W22 frame and shaft change with the number of poles, so the pole number should first be read from the speed on the plate, and then frame and shaft should be verified. This article shows in which order to check output, speed and frame compatibility for your 7.5 kW W22 motor and which data to pass to DRG MOTOR.

Grey three-phase electric motor with DRG MOTOR logo – output, speed and frame check for a WEG W22 7.5 kW renewal

Same 7.5 kW, three different frames

According to the W22 IE3 50 Hz tables in WEG's European catalogue, the 7.5 kW motor is listed in a 132S frame at 2940 rpm with 2 poles, a 132S/M frame at 1465 rpm with 4 poles, and a 160M frame at 975 rpm with 6 poles. The shaft is 38k6×80 mm on the 132 frames and 42k6×110 mm on 160M.

This table alone shows that matching the output does not mean the replacement is suitable. If a 4-pole 7.5 kW motor is considered for a 6-pole 7.5 kW position, shaft height (from 160 to 132), shaft diameter and machine speed all change.

Separate speed class from rated speed

"1500 rpm motor" describes a class; the plate shows the actual speed under load. For the 4-pole 7.5 kW W22 IE3 motor the catalogue gives 1465 rpm, while the rated speed of the DRG DRG-132M-4 model is 1460 rpm. The difference is small, but it should be considered where speed matters (e.g. a line set by pulley ratio). Write down the speed on your plate exactly.

Rated speed and frequency (50 or 60 Hz) should be read together; a 60 Hz plate shows different speed values.

Frame and shaft compatibility: what does 132S/M mean?

The catalogue shows the frame of the 4-pole 7.5 kW W22 IE3 as "132S/M". The longitudinal foot-hole spacing of the existing motor must be verified by measuring it on site and comparing it with the relevant technical drawing. Along with the longitudinal distance (B), also measure the transverse distance (A) and the distance from the shaft shoulder to the first foot hole (C). For the DRG-132M-4 model these values are A=216, B=178, C=89 mm.

Poles / speed classW22 IE3 frame and shaft (catalogue)DRG optionDRG frame, shaft, rated speed
2 poles / 3000132S – 38k6×80DRG-132S2-2132S – 38×80 – 2930 rpm
4 poles / 1500132S/M – 38k6×80DRG-132M-4132M – 38×80 – 1460 rpm
6 poles / 1000160M – 42k6×110DRG-160M-6160M – 42×110 – 970 rpm

The DRG models in the table are examples for comparison; suitability cannot be stated before foot dimensions, flange and overall length are checked. When you send your plate photo and measured A, B, C and shaft values to DRG MOTOR, the option can be examined with these data.

Housing material: cast iron and aluminium

In the W22 catalogue every frame is FC-200 cast iron. The DRG range offers both cast iron and aluminium housing electric motors at 7.5 kW; the three models above are listed in both materials. A vibrating base, an impact-prone location or a support designed for the weight of the existing motor are taken into account. For the full range see the DRG MOTOR shop.

Load and torque

At the same output, rated torque is inversely proportional to speed. In DRG data the rated torque at 7.5 kW is 24.4 Nm with 2 poles, 49.1 Nm with 4 poles and 73.8 Nm with 6 poles. Whether the machine struggles at start-up, whether it stops and starts frequently and what current the existing motor draws (see the motor current chart to compare with the plate current) decide whether the output level should be kept. If the motor failed, investigating the cause (overload, misalignment, moisture) comes before selection.

Questions on replacing a 7.5 kW W22

My plate says 1465 rpm; is a DRG motor with 1460 rpm suitable?

Both are in the 1500 rpm class. The difference is small but should be evaluated where speed is critical; suitability also depends on frame, shaft and mounting dimensions.

Can a 4-pole motor be considered instead of a 6-pole 7.5 kW?

That changes the machine's speed and torque demand, and the frame drops from 160M to 132. This change is not advisable without recalculating the pulley or gearbox ratio; competent people who know the machine side need to assess it.

If the shaft size matches, can the motor be swapped?

The shaft is only one of the dimensions to check. Foot spacing, shaft height, flange and overall length must also be compared.

Information to send to DRG MOTOR

  • Photo of the W22 plate: kW, rated speed, frequency, frame code, voltage and current
  • Number of poles (from the rated speed) and the speed the machine requires
  • Foot dimensions A, B, C and shaft height
  • Shaft diameter×length, key width; flange diameters if flanged
  • Drive type (coupling, pulley and belt, gearbox) and pulley diameters
  • Starting condition, daily operating hours and ambient data
  • Preferred housing material (cast iron or aluminium)

DRG Motor is a manufacturer, supplier and seller of electric motors. Send your 7.5 kW motor's plate, dimensions and machine data; the option will be evaluated by reviewing output, speed and frame data together with operating conditions. You can write via WhatsApp, use the quote list, call +90 (542) 666 11 11 or e-mail info@drgmotor.com (contact page).

See current prices of DRG MOTOR electric motors and order online in our storeSEE PRICES →

Technical Sources

  • WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — 17 Electrical Data: W22 Premium Efficiency IE3 (50Hz) 2, 4 and 6-pole tables — PDF page 40–42 (printed page 40–42).
  • WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — 18 Mechanical Data: shaft end dimensions (D×E) — PDF page 71 (printed page 71).
  • WEG — W22 Three-Phase Technical Catalogue, European Market (Cod 50025712) — Rev 34, 09/2026 — 15 Construction Features: FC-200 cast iron frame — PDF page 24 (printed page 24).